
Buy at
BanggoodWhere to buy? find more retailer
21g Eachine UZ65 65mm 1S Whoop FPV Racing Drone BNF Runcam Nano3 35mm Propeller 5.8G 25~100mW VTX
Specifications:
Brand Name: Eachine
Item Name: UZ65 65mm FPV Racing Drone
Wheelbase: 65mm
Size: 80mm*80mm*40mm
Weight(without battery): 21g
Weight(with battery): 29g
Receiver option:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
External DSM2/DSMX Receiver version(Compatible with Spektrum DX6I/DX7/DX8/DX9)
External TBS Crossfire Nano RX version(Compatible with TBS transmitter)
Features:
The smallest 1-2s 3 in 1 flight controller built-in ESC, Receiver
The world first 65mm whoop with 35mm propellers
Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
Smooth and powerful
Compatible for 1S Lipo/LIHV
Camera Angle adjustable
Spare parts specifications:
Motor | Mode: SE0802 19000KV Configu-ration:9N12P Stator Diamter:8mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm Weight(g):1.9g No.of Cells(Lipo):1S only |
Propellers | HQPROP 35mm-3blades Center Thickness:5mm Prop Diameter:35mm Center Hole Inner diameter:1.0mm |
Flight controller | Frsky SPI RX version Firmware target: CrazybeeF4FR Flysky SPI RX version Firmware target: CrazybeeF4FS DSM2/DSMX External RX version Firmware target:CrazybeeF4DX TBS Crossfire External RX version Firmware target: CrazybeeF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-2S battery input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in SPI Frsky/Flysky receiver Built-in 5V 1A BEC Built-in voltage detection |
Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_5_REV16_7.HEX Default protocol: DSHOT600 |
Onboard Frsky SPI D8 receiver Version | SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model Channels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m |
Onboard Flysky SPI receiver Version |
SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m Failsafe support |
5.8G VTX | Output power: 25mw~100mw Frequency: 40CH Input voltage: 3.3V~5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smartaudio ready |
Runcam Nano3 | Model: RunCam Nano 3 Image Sensor: 1/3" CMOS Horizontal Resolution: 800TVL Lens : 2.1mm(M8) FOV 160° Signal System: PAL/NTSC Non Switchable S/N Ratio: >50dB Electronic Shutter Speed: Auto Auto Gain Control (AGC): Auto Min. Illumination: [email protected] D-WDR: Auto Day/Night: Color Power:DC 3-5.5V Current: [email protected] [email protected] Housing Material: ABS Net Weight: 1.2g Dimensions: L14mm*W14mm*H9mm |
Lipo Battery |
Capacity:300mAh |
Package includes:
1 x UZ65 65mm 1S 65mm whoop Drone Frame
1 x SPI Receiver Option1: Superbee F4 FC built-in Frsky SPI D8 RX
SPI Receiver Option2: Superbee F4 FC built-in Flysky SPI RX
External Receiver Option3: Superbee F4 FC built-in DSM2/DSMX RX
External Receiver Option4: Superbee F4 FC built-in TBS crossfire RX
4 x SE0802 KV19000 brushless motor
1 x HQPROP 35mm-3 blades Propellers(4cw+4ccw)
1 x Runcam Nano3 1/3 CMOS 800TVL camera
1 x 5.8G 25mw-100mw 40ch vtx
4 x 1S 300mah 30C LiHV Battery
1 x 1S Lipo/LIHV USB Charger
1 x Propeller disassemble tool
1 x Eachine Handbag
Wholesale
Awesome, but I wish it came with Betaflight 4.2 and ExpressLRS
I installed a HappyModel EP2 ExpressLRS receiver below the flight controller on UART1 and the range is awesome now on only 10mw. I recommend that. I just wish it would come with Betaflight 4.2 for better OSD features such as the improved LQ format, etc. I'm too afraid / inexperienced to dare upgrading Betaflight yet.
Disapointed
spent nearly two days figuring out how to use betaflight and bind. The antenna fell off and one of the motors didn't work. Not only is it a piece of junk, it's misleading to suggest it is suitable for a first drone.
Your review is submitted successfully!
We will process your review within 1-5 business days.