Specification:
Brand: Eachine
Item Name: AE65 Crazybee X V1.0 Flight Controller
Flight Controller |
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection) Board Size: 28.5 * 28.5mm Power Supply: 1S-2S Battery Input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4In1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky Receiver Support D8/D16 Built-in 5V 1A BEC Built-in Voltage Detection Firmware Target: CRAZYBEEF4FR
|
Onboard 4 In 1 ESC
|
EFM8BB21
Power Supply: 1-2S LiPo/LiPo HV Current: 5A Continuous, Peak 6A (3 seconds) Support BLHeliSuite Programmable Factory Firmware: S_H_50_REV16_7.HEX Default Protocol: DSHOT600
|
(CrazybeeX FR V1.0 version)
Onboard Frsky SPI receiver
|
SPI BUS Receiver Frsky D8/D16 Compatible
Support for Futaba S-FHSS (Need Betaflight 4.0.5 firmware or latest), Frsky_X_LBT(EU-LBT)
Channels: 8CH / 16CH Failsafe Support No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
|
(CrazybeeX FS V1.0 version)
Onboard Flysky SPI receiver
|
SPI BUS Receiver
Protocol: AFHDS and AFHDS-2A Switchable Channels: 8CH(AFHDS) or 14CH(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m Failsafe Support
|
(CrazybeeX PNP V1.0 version)
|
No onboard SPI receiver
|
Onboard 5.8g VTX
|
Output Power: 25mw
Frequency: 40CH Input Voltage: 3.3V 5.5V Current Consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smartaudio Ready Default vtx_power should set to be “2”
|
Onboard Voltage and Current detector
|
Voltage Meter Scale “110” Amperage Mete Scale “1175”
|
Features:
CrazybeeX FR V1.0 Bind procedure:
- Make the on board receiver get into bind mode: For 3.5.7 version firmware Plug USB and then press the bind button for 1 second , the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”
- Make your Frsky transmitter get into bind mode . If bind is successful the red led will starting to blink. The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio , but the bind is actual successful , need to go to CLI command and type “save” to finish the binding .
CrazybeeX FS V1.0 Bind procedure:
- Make the on board receiver get into bind mode: For 3.5.7 version firmware Press and hold the bind button for 1 second ,then plug USB, the Red LED at the bottom of the flight controller will blinking fast , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED at the bottom of the flight controller will blinking fast , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”
- Make your Flysky transmitter get into bind mode . If bind is successful the red led will getting to be solid.
Package Included:
1 X Eachine AE65 Crazybee X V1.0 Flight Controller (Optional)